ECT vs Mullen Test: Box Strength Ratings and the Conversion Chart
Updated · Vorex Packaging
ECT (edge crush test) and the Mullen burst test are two ways to rate corrugated board. ECT measures edge crush strength in pounds per inch and predicts stacking; Mullen measures the force to burst the board face, in pounds such as 200#, and relates to rough handling. They share the same load limits: a single wall 32 ECT box and a 200# Mullen box are both rated for up to 65 lb and 75 in of combined length, width and depth.
The short answer
The edge crush test (ECT) and the Mullen burst test are two ways to rate the strength of corrugated board. ECT measures how much force the board takes on its edge before it crushes, in pounds per inch of edge, and predicts how well a box stacks. Mullen measures the force needed to burst through the face of the board, reported in pounds such as 200#, and relates to rough handling and puncture. The two are rated against the same load limits, so a single wall 32 ECT box and a 200# Mullen box are both rated for up to 65 lb and 75 in of combined length, width and depth.
What does the edge crush test measure?
A small strip of corrugated board is stood on its edge between two flat plates, with the flutes running in the direction of the load, and pressed until it fails. The peak load is reported in pounds per lineal inch of the loaded edge and written as an ECT value, for example 32 ECT. Because a box standing in a stack carries its load on the edges of its walls, ECT is the rating that tracks stacking strength on a pallet, in a warehouse or in a delivery van.
What does the Mullen burst test measure?
The Mullen test presses on the flat face of the board until it ruptures, and reports that burst strength in pounds (125#, 200#, 275# and so on). It is the older of the two standards. Burst strength relates to how well the board resists punctures and knocks from outside and pressure from the contents inside, which is why it is linked to rough handling rather than stacking.
ECT to Mullen conversion chart
These are the industry equivalency rows: each Mullen grade and its matching ECT grade, with the heaviest load and the largest outside size (length + width + depth added together) that the grade is rated for.
| Max weight of box and contents | Max outside length + width + depth | Mullen (burst) | Edge crush test |
|---|---|---|---|
| 20 lb | 40 in | 125# | 23 ECT |
| 35 lb | 50 in | 150# | 26 ECT |
| 50 lb | 60 in | 175# | 29 ECT |
| 65 lb | 75 in | 200# | 32 ECT |
| 80 lb | 85 in | 250# | 40 ECT |
| 95 lb | 95 in | 275# | 44 ECT |
| 120 lb | 105 in | 350# | 55 ECT |
Single wall corrugated boxes.
| Max weight of box and contents | Max outside length + width + depth | Mullen (burst) | Edge crush test |
|---|---|---|---|
| 100 lb | 95 in | 275# | 48 ECT |
| 120 lb | 105 in | 350# | 51 ECT |
| 140 lb | 110 in | 400# | 61 ECT |
| 160 lb | 115 in | 500# | 71 ECT |
| 180 lb | 120 in | 600# | 82 ECT |
Double wall corrugated boxes.
| Max weight of box and contents | Max outside length + width + depth | Mullen (burst) | Edge crush test |
|---|---|---|---|
| 240 lb | 110 in | 700# | 67 ECT |
| 260 lb | 115 in | 900# | 80 ECT |
| 280 lb | 120 in | 1100# | 90 ECT |
| 300 lb | 125 in | 1300# | 112 ECT |
Triple wall corrugated boxes.
To use it: weigh the product with all its packing, add up the box's outside length, width and depth, and go to the first row where both numbers fit. Our ECT calculator does the lookup for you. The row is a minimum; fragile goods, long storage or high stacks are good reasons to go one grade up.
Why are there two ratings for the same box?
The Mullen rating comes with a minimum basis weight for the papers in the board: the liners must weigh at least a set amount per area. ECT dropped that requirement and rates the finished board on its performance instead. So for two boxes of the same size and rated strength, the ECT-rated one is usually lighter because it uses less material, which also trims shipping weight.
ECT or Mullen: which one should you choose?
- Boxes that stack (pallets, shelves, warehouse storage, subscription boxes stored before dispatch): choose by ECT, the test that predicts stacking.
- Heavy single parcels that get thrown, dropped or knocked, or contents with sharp corners: a burst (Mullen) rating speaks to puncture and rough handling.
- Light e-commerce products in printed mailers: the board is chosen for print quality as much as strength. Our printed mailer boxes use thin E-flute corrugated, about 1/16 in thick; heavier products move to shipping boxes or double wall boxes.
If you are not sure, send us the product, its weight and how it ships, and the board is set in your quote before anything is printed.
How do you read the box maker's certificate?
Boxes made to the freight classification rule for fiberboard boxes (NMFC Item 222) carry a round box maker's certificate printed on an outside surface, about 3 inches across. There are two versions: one for boxes made to the burst (Mullen) table and one for boxes made to the edge crush table. The stamp names the box maker and the rated limits, so you can see at a glance whether a box was built to a Mullen or an ECT grade. These are freight (LTL) rules; parcel carriers publish their own packing guidelines, so check your carrier's as well.
A worked example
A 12 x 10 x 8 in box adds up to 30 in. Packed with a 30 lb product it needs a grade rated for at least 30 lb and 30 in: in the single wall chart that is the 26 ECT / 150# row (35 lb, 50 in). If the same box will sit at the bottom of a pallet or holds glass, a 32 ECT / 200# board gives more margin. At 70 lb the single wall options start at 40 ECT / 250#; past 120 lb you are into double wall.
Corrugated boxes we make: corrugated mailer boxes and double wall trays; the board grade for your weight is confirmed with your quote.
Box sizes in this guide
Each size has its own page with the box styles and products at that size, a dieline and a quote form with the size filled in.
Sources
All read on 4 Nov 2026:
- Crown Packaging, Mullen Test vs. Edge Crush Test Boxes (test definitions, strength equivalency charts, basis weight difference).
- Fibre Box Association, NMFTA Items, reproducing NMF 100 Item 222 (certificate of box manufacturer, definitions of length, width, depth and ECT).









